This ad is for a used OEM heater fan speed motor control resistor for a 1984 - 1989 Porsche 911 Carrera with a automatic heater fan speed control feature. The resistor is in very good condition and comes with the harness. The Porsche part number for the resistor is 911.616.011.00 I am asking $60.00 for the part plus $9.50 in postage and paypal fees
This ad is for one used OEM temperature sending units for a 1978 - 1983 Porsche 911SC and most like will fit other Porsche year and models like the Carrera and Turbo as well so please do your homework to insure it is correct for your needs. Each is in perfect working order and ready for installation on your engine. The Porsche part number is 930.606.117.01 I am asking $50.00 for the part plus $...
We are parting out a 2010 DODGE CHARGER, 151k miles. What parts are you looking for Read list belowMotor - SOLDCenter console - SOLDPassenger front door - SOLDWheels tires - SOLDWE HAVETransmission- $375.Drivers door - $125drivers rear door - $125passenger rear door - $125trunk lid - $75rear bumper - $100Engine wiring harness 3.5 - $149.Carpet black - $100Seats full set grey cloth- $200Rear doo...
I have a complete 5.3 engine with all accessories. 79,125 miles. Engine pulled from a 2005 chevy suburban 4x4 that was wrecked. Will guarantee and installation available. Im located at 3004 East Broadway, North little Rock, Ar. 72114. My name is Beau, and my number is . Transmission not included in this price. The transmission is an additional 600.
Good used Gates brand drive belt and tensioner combo, removed from a 5.7 350 Vortec , 1998 Silverado, with low miles of use. Should fit a lot of years with the vortec 350 engine. No cracks in belt and bearings feel fine on the pulleys. $30.00 cash This combo kit is over a hundred bucks if bought new at Oreillys.Items are in Heber Springs, u gotta come here. Meet at publicbusiness location.Text ...
Military Surplus Detroit Diesel Engine in-line 6 cylinder. This was rebuilt by the military, but has some damage from being mis-handled. The oil pan, valve cover and starter are damaged, otherwise it all seems to be intact. Asking $1,500
Military Surplus Detroit Diesel Engine in-line 6 cylinder. This was rebuilt by the military, but has some damage from being mis-handled. The oil pan, valve cover and starter are damaged, otherwise it all seems to be intact. Asking $1,500
I have the engine is 4.0, right side front door $250, all the seats - front seats$70 each and the rear seats $100, speedometer$40, all inside trims, gas tank with the fuel pump $150, three wheels 16 in$50 each, front spindles and lower front control arms. The rank and pinion $70, Upper Control Arm $50, tailgate $150, fender $50, automotive reinforcement $70, passenger airbag $80,2 left side win...
Never used Downey ceramic coated headers for a Toyota 3VZE V6 engine. I bought these new for a 91 truck, but never got around to putting them in. Do your own research to verify theyll fit for your application. Includes gasket kit. $90 or best offer. text only
2005 Dodge Ram 3500 5.9 Diesel engine wiring harness 600$ cost 850 its brand new in box from Cummins. Ill throw in a few other parts for the 05. Map sensor- fuel regulator, etc.
I have a complete good running Volkswagen Jetta 2.5 5 cylinder engine with 101,000 miles car was hit in the rear drivers side and totalled out I used trans in other Jetta and have no use for engine.$400.00 or trade and cash
I am parting out a 1980 CJ5. You can buy as is or come and get any part you might need from it. The prices will vary depending upon what you are wanting. Motor run 1 year ago but hasnt been started since. It has a 4 speed standard transmission. I am also willing to trade it for a 16ft trailer with dual axles and rs.
350 chevy engine just rebuilt from top to bottom all new parts. bored .040 over crank is 1010 heads are 202194. high vol oil pump double roll timimg chain new oil pan timing chain cover edlebrock intake that has been powder coated edelbrock valve covers comp cam 454464 lift comp cam roller rockers ready to set in.
We are parting out a 2010 DODGE CHARGER, 151k miles. What parts are you looking for Read list belowWHEELS - SOLDMotor - SOLDCenter console - SOLDPassenger front door - SOLDWheels tires - SOLDDrivers door - Damageddrivers rear door - SOLDWE HAVETransmission- $250passenger rear door - $125trunk lid - $75rear bumper - $100Engine wiring harness 3.5 - SOLDCarpet black - SOLDSeats FRONT grey cloth- $...
We are parting out a 2010 DODGE CHARGER, 151k miles. What parts are you looking for Read list belowWHEELS - SOLDMotor - SOLDCenter console - SOLDPassenger front door - SOLDWheels tires - SOLDDrivers door - Damageddrivers rear door - SOLDWE HAVETransmission- $250passenger rear door - $125trunk lid - $75rear bumper - $100Engine wiring harness 3.5 - SOLDCarpet black - SOLDSeats FRONT grey cloth- $...
This ad is for a used set of OEM camshaft housings / cam towers for a 1969 Porsche 911 E with MFI. These camshaft housings fit a 1968 Porsche 911 model and up. Please do your homework to insure they are correct for your needs. They are in very good condition. I cleaned them a bit but they still need further cleaning especially on the mounting side. If you are building a 1969 911 E MFI engine, I...
This ad is for a set of six used OEM connecting rods for a 1965 - 1970 Porsche 911 2.0 liter and or a 1970 - 1972 Porsche 914-6 2.0 liter. I believe these connecting rods are also correct the 2.2 liter engines but please do your homework to ensure that these are correct for your application. I will help answer questions if I can or make additional photographs if necessary. The Porsche part numb...
This ad is for a set of transmission and or motor mounts for a 1965 - 1989 Porsche 911 and or a Porsche 930 or 912E. The mounts are very well made and look to be new. Not sure of the maker but they are done well. The Porsche part number is 911.375.043.00 I am asking $50.00 for the set plus $9.50 in postage and paypal fees