NO TEXT MESSAGESPHONE CALLS ONLYNEW Blueprint Engines 400 Small Block Chevy Bare block. Features 9.025 Deck Height, 4 bolt spayed Main caps, 2 Piece Rear Main Seal, Main Priority oil system. Unfinished bores. Will need to be bored to your finish specs. Has a small neck to one cylinder top edge as can be seen in picture. $1400.00 Again Call only, NO text messaging, too many scammers.
This ad is for a used factory original bulkhead engine mount bracket for the 1970 - 1972 Porsche 914-6 2.0 liter. This bolts to the pulley end of the engine. This is not an aftermarket engine mount but an original factory part. I am not sure what other parts are needed to make this work as originally configured. I suspect the bulkhead of a factory original is configured to accept this part. I s...
This ad is for a set of left and right OEM engine baffle plates for a 1970 - 1976 Porsche 914-4 automobile. Since the VW TIV is very similar to the Porsche TIV these baffle plates may fit a VW with a TIV style engine. Please do your homework to insure these are correct for your application. The engine baffle plates are no longer available from the factory and I have several sets. Some like thes...
Motor has only 50,000 actual miles. Transmission is also available with same mileage. Some body parts are intact.
This intake is off of a 5.0L Coyote mustang Gt fits 11-present mustangs and for the F-150 guys this will also fit 5.0 Coyote trucks for higher rpm HP and torque. Plus engine cover Kit included. Also fit 11-present mustangs and 5.0 F150. Im selling so cheap by i no longer need them. Only asking $200 OBO. Call Danny for more info
Good SBC 305 engine out of 83 El camino 119k miles runs and performs goodYou can hear it run for the next couple of days or have a video of it running if I have already pulled it. From intake to pan including distributor no carb front accessories will bea serpentine set up $400. firmif you see the ad it is available
You are viewing a 2005 FORD MUSTANG GT MOTOR - 4.6 3v ENGINE. Fits a 05-09. Has 136k miles. Runs great. I can send a video of it running. Located in Conway, Arkansas. FOR FASTER RESPONSE, call or text me 4797472695 Thanks for looking at our ad, but before you go do you know the Lord, Jesus Christ as your Saviour If not, dont wait until it is eternally too late. You are only one heartbeat away f...
4.8 Vortec motor $800 4L60E transmission- $700 transfer case- $400 10 bolt 6 lug rear end- $500Out of 04 GMC 1500. Wiring harness has been cut, but motor does run. Everything in working condition. $2200 for ALL or will separate
This ad is for a new OEM engine sheet metal fastener kit for a 1974 - 1977 Porsche 911. Dress up your engine shroud and sheet metal with fresh new bolts and washers. I am asking $45.00 for the kit plus $7.50 in postage and paypal fees
This ad is for a used OEM Bosch starter motor for a 1970 - 1976 Porsche 914-4 and or a 914-6. This Bosch starter motor also fits a 1965 - 1971 Porsche 911 / 912. I have three of these starter motors in an unknown condition. At a minimum consider them cores. The Bendix gear is not wobbly nor does it show serious signs of wear The Porsche part number is 901 604 102 03. I am asking $60.00 for this...
This ad is for a used OEM lower engine lid latch for a 1965 - 1989 Porsche 911 and or a Porsche 930. The latch is in good condition and aside from needing a thorough cleaning it is ready for installation. The Porsche part number for the latch is 901.512.052.00 I am asking $75.00 for the part plus $10.50 in postage and paypal fees
This ad is for a used OEM engine shroud with the wiring harness for a 1974 - 1977 Porsche 911S and the Carrera with a 2.7 liter engine. As you can see the shroud also comes with the left and right air sockets or air guides. I don't see a thing wrong with the setup. The wiring harness is complete and the wires are not stiff and brittle. There is normal wear and tear on the shroud and one or more...
over a month agoLittle Rock, AR+14 milesAuto Parts for Sale
This ad is for two MOS through bolt chamfered washers for a case nut of a 3.0 liter Porsche 911 and or Porsche 930. I think this washer was changed from a flat washer 1965 - 1974 and then beginning with engines with a 90 mm bore or larger the chamfer was added to prevent them from interfering with the cylinder fit and holding up the base of the larger diameter cylinders thus causing them to not...
over a month agoLittle Rock, AR+14 milesAuto Parts for Sale
This ad is for a used OEM engine lid grill for a 1970 - 1976 Porsche 914. The grill is in good condition. Basically what you see is what you get. The Porsche part number is I am asking $80.00 for the lid plus $28.50 in postage and paypal fees
over a month agoLittle Rock, AR+14 milesAuto Parts for Sale
This ad is for a used custom engine lid for what is thought to be a 1974 - 1977 Porsche 930 Turbo without the inter cooler. I am not at all sure of this so please do your homework to insure this is correct for your needs. This is a very unusual design and what is not noticeable is that the fiberglass lid itself is bonded to the factory steel sub frame. This is how the factory built the historic...
over a month agoLittle Rock, AR+14 milesAuto Parts for Sale
This ad is for a used OEM engine lid grill with rain tray for a 1970 - 1976 Porsche 914. The grill is in outstanding condition but unfortunately it got scratched and scuffed while in storage. It is missing the Porsche letters. I believe the scuff and scratch can be buffed out with a mild polishing compound. The Porsche part number for the lid is 914.512.022.10 The Porsche part number for the gr...
over a month agoLittle Rock, AR+14 milesAuto Parts for Sale
This ad is for a used OEM rear engine lid assembly with a turbo style rubber spoiler added for a 1974 - 1989 Porsche 911 and or a Porsche 930 Turbo. This engine lid assembly is often called a whale tail and sometimes a "tea tray" it comes stock on a Porsche 930 Turbo and the cars with the M491 wide body kit to make a narrow body car into a Turbo look Porsche 911. This particular engine lid is a...
over a month agoLittle Rock, AR+14 milesAuto Parts for Sale
This ad is for a used OEM engine lid latch assembly with pull cable and knob for a 1970 - 1976 Porsche 914-4 and or a 914-6. This parts are in good condition and aside from a good thorough cleaning they are ready for installation. Lubricate the cable before installing it. The Porsche part number for the latch is 914.512.029.10 The Porsche part number for the lid release cable 914.511.091.10 I a...
over a month agoLittle Rock, AR+14 milesAuto Parts for Sale
This ad is for a new custom engine lid grille for a 1974 - 1989 Porsche 911 / 912E and or a Porsche 930. Although the grill will fit the 1969 - 1973 Porsche 911 and Porsche 912 models as well. This is a lightweight, retro-cool, perforated-metal grille for the 911. The grille is made from sheet aluminum and has been powder coated black. It comes with the hardware and mounting instructions. It is...
over a month agoLittle Rock, AR+14 milesAuto Parts for Sale
This engine came from a 1982 F150 pickup. The truck sat since 2012. To get it running I replaced the plugs fuel pump. It starts right up and runs very well. No smoke, no knocks and no funny noises. It showed normal oil pressure on the Ford dash gauge. I have no idea how many miles are on the engine or anything about the internal condition. I did notice some oil at the front of the intake block ...